A smart lock that won't pair, or that locks and unlocks fine by hand but looks offline in the app, is almost never a dead unit. Locks fail to connect in a different way than plugs or bulbs do, because most of them actually run two separate connections — a short-range Bluetooth link to your phone, and a longer-range Wi-Fi or bridge connection for remote access — and it's easy to fix one while never realizing the other is the actual problem.

Below is the order worth checking things in, starting with the fix that resolves the most cases, plus how to tell whether you're dealing with a pairing problem, a remote-access problem, or a dead battery wearing a connectivity disguise.

Ready to compare specific models? Jump to our best smart locks roundup for current picks, pros and cons, and pricing.

First, figure out which connection is actually broken

Most retrofit and full-replacement locks, including the August Wi-Fi Smart Lock and Level Lock+, use Bluetooth to talk to your phone when you're near the door and a separate Wi-Fi connection (built in on some models, added via a bridge accessory on others) for locking or checking status from away from home. A lock that responds instantly to the app while you're standing next to the door but never shows a current status from work is a remote-access problem, not a pairing problem — the Bluetooth link is fine, and the issue is the Wi-Fi or bridge side.

That distinction matters because the fixes are different. Treat 'won't pair with my phone at all' and 'works locally but not remotely' as two separate troubleshooting paths rather than assuming one fix covers both.

Bluetooth pairing fails or times out

The most common cause is simply distance or a phone's Bluetooth being toggled off in the background — stand within a few feet of the lock, confirm Bluetooth is on in your phone's settings (not just the lock app's permissions screen), and try again. If the lock's companion app shows a persistent 'searching' state, close and reopen the app rather than letting it keep searching; most lock apps handle a fresh pairing attempt more reliably than a long-running one.

If pairing still fails, check that the lock isn't already paired to another phone or account from a previous owner or a setup attempt that didn't finish cleanly — a lock that thinks it's already claimed won't finish pairing with a second device until it's removed from the first account or factory reset.

Locks fine by hand, but the app shows it offline or unresponsive

On locks with built-in Wi-Fi, like the Schlage Encode Plus and Schlage Encode WiFi Deadbolt, this almost always traces back to the same 2.4GHz-only limitation that trips up smart plugs and bulbs — if your router auto-assigns devices across a combined 2.4GHz/5GHz network name, the lock can get pushed onto the band it can't join. Split the bands temporarily (look for a 'smart connect' or band-steering toggle), re-add the lock while it only sees the 2.4GHz network, then turn band steering back on once it's connected.

On locks that rely on a separate bridge instead of built-in Wi-Fi — a Level Lock+ with the Level Connect Wi-Fi Bridge, or a Yale Assure Lock 2 with a Wi-Fi connectivity module — check the bridge itself first. The lock's local Bluetooth behavior tells you nothing about whether the bridge is online; its own status light or app entry is the thing to check, and a bridge that's lost power or been unplugged (easy to do if it's a small puck shoved behind furniture) will make every lock connected to it look 'offline' for remote access while locking normally by hand.

A fresh battery change breaks the connection temporarily

Pulling the batteries, even briefly, resets most locks' radio connection, and some models need a minute or two to rejoin Wi-Fi or re-establish with a paired bridge afterward — don't assume it's broken if it doesn't show connected the instant new batteries go in. If it's still offline after several minutes, open the app and check for a pending firmware update; some locks, including several Kwikset and Yale models, pause normal connectivity status until a stalled update finishes or is retried.

Low (not dead) batteries cause a subtler version of the same problem: the lock has enough power to physically turn the deadbolt but not enough to reliably hold a Wi-Fi or Bluetooth connection, which shows up as intermittent 'offline' notifications well before the low-battery warning actually fires. If disconnects are getting more frequent rather than constant, try fresh batteries before anything else.

When to stop troubleshooting and check the bridge or router instead

If you've confirmed Bluetooth pairing works fine up close but remote access never comes back no matter what you try, the bridge or router is a much more likely culprit than the lock itself — try power-cycling the bridge (unplug for about 10 seconds) and confirming it still shows up on your Wi-Fi network before troubleshooting the lock any further.

If you're shopping for a replacement and want to avoid the extra bridge-dependency failure point entirely, our best smart locks roundup notes which current picks include Wi-Fi built in versus which need a separate bridge for remote access.

Frequently Asked Questions

My smart lock works fine by hand but shows offline in the app — what's wrong?
The lock itself and its Bluetooth connection to your phone are working — what's broken is the Wi-Fi or bridge connection used for remote access and status updates. Check the lock's Wi-Fi band (2.4GHz only on most models) if it has built-in Wi-Fi, or check that its separate bridge accessory is still powered and online if it uses one.
Do I need a separate bridge for every smart lock's remote access?
No — it depends on the model. Locks like the Schlage Encode Plus and Schlage Encode WiFi Deadbolt include Wi-Fi directly, while others, like the Level Lock+ or a Yale Assure Lock 2 without its Wi-Fi module installed, need a separate bridge or module purchased and set up for remote access to work at all.
Should I factory reset a smart lock that won't connect?
Not as a first step. Check Bluetooth range, Wi-Fi band, and bridge power first, since a factory reset erases the lock's pairing and guest codes entirely. Reset it only if it won't respond to pairing at all after you've ruled out those more common causes.
Why did my smart lock go offline right after I changed the batteries?
Changing batteries resets most locks' radio connection, and it can take a minute or two to rejoin Wi-Fi or reconnect to a paired bridge afterward. If it's still offline well after that, check for a stalled firmware update in the app before assuming it's a hardware problem.

Keep reading